ASTM A787 PDF

ASTM A/AM: Standard Specification for Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing. A Mechanical Tubing. ASTM A includes steel grades from – Alro stocks A as welded mechanical tubing. A Tube includes a wide. Designation: A – Standard Specification for. Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing1 This standard is issued.

Author: Faejinn Tanos
Country: Equatorial Guinea
Language: English (Spanish)
Genre: Relationship
Published (Last): 12 November 2009
Pages: 305
PDF File Size: 3.47 Mb
ePub File Size: 17.63 Mb
ISBN: 478-8-99411-456-8
Downloads: 41389
Price: Free* [*Free Regsitration Required]
Uploader: Gugis

The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.

ASTM A Tubing ,ASTM A Type 1,Type 2,Type 3,Type 4,Type 6,ASTM A | Superior Steel

ASTM A Type 3 welded mechanical tubing is produced out of a hot rolled carbon steel and then is hot-dip galvanized per ASTM A specification into a tank of molten zinc after the tubing is already formed and welded. The wstm stated in q787 SI units or inch-pound units are to be regarded separately as standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

A Type 6 Tubing provides a high degree of corrosion resistance and an excellent surface appearance and is a bridge between stainless and hot-dip galvanized finishes. Combining values from the two systems may result in non-conformance with the standard.

  ANDREW BACEVICH LIMITS OF POWER PDF

Historical Version s – view previous versions of standard. This abstract is a brief summary of the referenced standard. Within the text, the SI units are shown in brackets.

ASTM A787 Grade 1018

The values stated in each system may not be exact equivalents; therefore, aastm system shall be used independently of the other. Outside Diameter Tange, in.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. We manufacture of ASTM A TYPE 1 Tubingis produced using aluminized steel which is carbon steel that has been pre-coated on both sides with an aluminum silicon alloy while in coil form.

ASTM A Type 6 welded mechanical tubing is produced using steel that has been pre-coated with a thin layer of a zinc-aluminum-magnesium alloy coating while in coil form as specified in ASTM A The steels shall conform to elemental tolerances for product analysis. Link to Active This link will always route to the current Active version of the standard.

Sizes outside the ranges listed above may be ordered provided all other requirements of the specification are met.

A Mechanical Tubing | Alro Steel

Carbon Steel A Tube Exporter. Combining values from the two systems may result in non-conformance with the standard. This xstm is expressed in both inch-pound units and in SI units; however, unless the purchase order specifies the applicable M specification designation SI unitsthe inch-pound w787 shall apply.

  70L02H DATASHEET PDF

The values stated in either SI units or inch-pound units are to be regarded separately as standard. This guide covers standard specification for round, square, rectangular, and special shape, electric-resistance-welded mechanical tubing, either zinc-coated galvanized after welding or produced from aluminum-coated, zinc-coated galvanizedzinc-iron alloy-coated galvannealedor aluminum-zinc alloy-coated steel sheet.

Low-carbon steels and other carbon steels shall conform to the required chemical a7787 for carbon, manganese, phosphorus, and sulfur. Within the text, the SI units are shown in brackets. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. ASTM A Type 4 welded mechanical tubing is produced using carbon steel that has been pre-coated with a thin layer of zinc while in coil form aatm then heat treated to convert the coating into a zinc-iron alloy.

Wall thickness tolerances for premetallic coated as-welded tubing and diameter tolerances for metallic-coated round tubing shall be provided.