IRF9Z34N datasheet, IRF9Z34N circuit, IRF9Z34N data sheet: IRF – Power MOSFET(Vdss=V, Rds(on)=ohm, Id=A),alldatasheet, datasheet. IRF9Z34N Transistor Datasheet, IRF9Z34N Equivalent, PDF Data Sheets. MOSFET. Parameters and Characteristics. Electronic Component Catalog. Drain Current Mar Thermal Max Power. Resistance Dissipation. (°C/W). Part. Number on. Case. Demand Outline. (A). Number. Key. Through-Hole.

Author: Mazugis Zugami
Country: Guatemala
Language: English (Spanish)
Genre: Business
Published (Last): 26 November 2018
Pages: 495
PDF File Size: 12.65 Mb
ePub File Size: 10.46 Mb
ISBN: 719-3-57344-893-6
Downloads: 94734
Price: Free* [*Free Regsitration Required]
Uploader: Jujora

I mean ‘they’ will take care of this.

IRF9Z34N P-Channel Mosfet

datadheet The good thing is that you have pulsing from the PIA – he’s not dead. Q52, 54, 56, 58, 60, 62 and 64, as per this guide: I won’t have access to another System 11 until Monday at the earliest, but since GPE has them for 35 cents a pop, I may as well get them and datashwet sockets to go with them.

I see a steady high on the pin that takes in the blanking signal, a pulse on the pin that goes to the PIA, and a low on the output. All signs point to yes, but I’d like to get someone else’s confirmation. Would that be a better choice? When I reverse the leads, though, I get.

I figured it out. JPG With the red lead on the middle pin, and the black lead on the right pin on the top ones, I get. It’s hard to go wrong Linked Games Taxi Williams, That amounts to about a 1mA load — any of the above parts would work.


LS would probably be better. So I’m trying to figure out if the existing ‘s were damaged when I powered the machine on.

IRF9Z34N Datasheet

These aren’t for solenoid drivers, though. That is one hard-to-read page. Plain series parts are getting harder and harder to stock and cost has gone wayyy up. With the red lead on the middle pin, and the black lead on the right pin on the top ones, I get.

IRF9Z34N – Infineon Technologies

I get nothing when the same is done on the bottom ones. Here are the three datasheets for these ICs. Elsewhere it doesnt seem to matter on the driver board. Did you know Pinside is able to run thanks to donations from our visitors? Can anyone help me understand how Datxsheet can determine this stuff for myself?

Please donate to Pinside, support the site and get a next to your username to show for it! You’re testing it correctly. I’ll have to take it up with the people I ordered these parts from and be a bit more aware of the parts I get in the future. Certain page elements may have irf9z334n deliberately hidden. The current probably won’t be a big deal, but the fast edges can sometimes cause problems or even EMI electro-magnetic interference.

Shoot that “anonymous” source an email. So either I’m not performing my test correctly since I don’t have actual transistors or lamps ultimately hooked up to the output pins of these s or they’re both smoked.


I turned the machine on, with only a few lamps connected to the board. That could explain why the two that were connected to lamps proceeded to explode their pre-driver transistors.

TAXI datasheet hair version playfield. G-P-E’s right – the main spec that matters for that is that the minimum sink current be high. Need to use high current 74F or 74S here. One image has been uploaded to this topic. Q52, 54, 56, 58, 60, 62 and 64, as per this guide:. Those replacements arrived, and before putting them in, I compared them to the non-fried ones I had in there from my first order.

This page was optimised for printing.

IRF9Z34N Datasheet PDF – International Rectifier

I see I missed the important bit where UB said this is for the solenoid driver transistor thought they were just driving other logic.

TAXI red hair version playfield. Promoted items from the Pinside Marketplace.

I heard a pop, and immedately turned them off.