B SERVICE MANUAL , REV C Thank you for your purchase of the B Keurig Single Cup Brewing System! U U The B is the. the Cleaning Instructions in this guide. Turn off and unplug the brewer before cleaning or maintenance. Allow to cool before putting on or taking off parts. Download KEURIG B SM service manual & repair info for electronics experts.

Author: Yorg Fenrisho
Country: Uzbekistan
Language: English (Spanish)
Genre: Science
Published (Last): 14 October 2011
Pages: 344
PDF File Size: 6.26 Mb
ePub File Size: 19.31 Mb
ISBN: 481-3-75625-420-9
Downloads: 71080
Price: Free* [*Free Regsitration Required]
Uploader: Vudorg

The Hot Water Tank Module can be removed from the brewer. Cindy Wells Level 3 Expert Answers. Keurig requires the use of an 9. Or point us to the URL where the manual is located.

After tightening rotate the panel manhal back until it snaps closed.

Municipal water is introduced to the unitthrough the inlet valve [X]. Dispensing Hot Water The B brewer is capable of dispensing hot keurug for making hot chocolate, instant soups etc. Read all instructions before using this Note, some changers may require a slight deflection of the cabinet side panels during insertion. The entire brew process lasts for approximately 40 to 52 seconds depending upon brew size selected and ends with a burst of air to remove all liquid coffee or tea from the K-Cup.

Depending on the individual blend, up to approximately 9 to 14 grams of premium freshly ground coffee is added. Using a flat screw driver, gently pry Seefigures 4 and 5 below. After heating has taken place the display will read: De-scaling If you are experiencing any problems with pump or similar your Brewer, please contact you Keurig Step 2: Remove the plastic bar in front of the Main PCB and disconnect the three wire harness connections on b30000 board.


There are no component level repair capabilities for this brewer. This manial contains a KQ8A filter, filter head, and mounting bracket. Theyare captive screws so they manuak NOT come out completely.

The B Coin Changer Accessory is custom designed to be used exclusively with the B Commercial Brewer and the aforementioned coin mechanism. A choice of 4, 6, 8, and 10 oz cup sizes areavailable.

Posted on Nov 21, Be the first to answer. The K-Cup holder will open towards you. Disconnect the Hot Water Valve hose from the top of the bottom tank. Answer questions, earn points and help others Answer questions. The water in the brew tank is forced out of the tank through the integral brew tube [L] in the upper hot water tank cover.

Keurig B3000 Use & Care Manual

The Control Panel Module can now be removed. You will see one small hose and two larger ones.

Tilt the module toward you. Depending on the mineral content of the water C We recommend that customers leave the brewer powered on at all times as it has built-in safety shutoffs, uses minimal energy, and offers the convenience of a fresh cup of coffee or tea at any time. Loosen the captive screws holding the Power Module in place.

Remove the poly foam packaging material surroundings the brewer. The items included in the accessory kit are: If they are not, then there will be no water dispensed during the brew cycle.

The K-Cup holder will open towards you. You must scroll through all ten digits. Release the hose clamp and remove the brew tube from the entrance needle assembly. Coffee beans or ground coffee cannot beprocessed in this brewer. Answered on Oct 21, Municipal water is introduced to the unit through the inlet valve [X].


Disconnect the Cold Water Tank drain hose on the bottom right side of the tank. All the necessary hardware and cables for assembling the B Coin Changer Accessory are included. Draining the B Brewer Emptying the drip tray If you wish to drain the brewer, the following To empty the drip tray grasp the drip tray by steps should be followed: The path of the water delivery is separate from the coffee delivery path.

Within 4 seconds, push this RED button four times. The large Plastic Nut must be tight. Below is a maunal of all errors, their meanings and the menu messages.

After it has primed and heated, place a ceramic cup in the Drip Tray and run a brew cycle. The Puncture Mechanism Module can now be removed from the brewer. Power off the brewer and drain both hot and cold water tanks.


Remove RED retaining clip from Murdock fitting. Support the module with your hand. Platform Unit Part Number Ekurig assembly of the B Platform accessory is covered in the installation guide provide with each platform kit.